Search results

The purpose of this paper is to study the effects of operating conditions including process coefficient, lubricant viscosity and cavitation pressure on the cavitation of spiral groove liquid-film seal (SG-LFS).

A mathematical model of SG-LFS is established based on the JFO boundary and a relative density is introduced. The universal governing equation after a coordinate transformation is discretized by the FVM method and solved by the Gauss-Seidel relaxation scheme.

The results indicate that the two-dimensional size of cavitation and cavitation degree are affected significantly by the process coefficient and lubricant viscosity but the effect of cavitation pressure can be ignored.

The effect mechanisms of operating conditions on the cavitation of SG-LFS are studied by the JFO boundary and cavitation degree characterized by a relative density. The results presented are helpful to perfect and deeply understand the cavitation mechanism of liquid-film seal.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-03-2020-0083/

The purpose of this paper is to study the dynamic characteristics of mechanical face seals with liquid-lubricated inclined elliptical grooves.

The steady-state and perturbation Reynolds control equations of liquid films were established. The film pressure and the liquid film dynamic coefficients were obtained, impacts of groove structures on the liquid film dynamic characteristic coefficients were analyzed.

The analysis results indicate that the axial dynamic stiffness and damping coefficients of the liquid film seal with inclined elliptical grooves are far greater than those of the angular directions. Furthermore, the dynamic stiffness coefficient of the liquid film with the nonclosed inclined elliptical grooves is higher than those with the closed grooves, whereas the dynamic damping coefficient of the liquid film is lower.

The effects of inclined elliptical groove structures on the dynamic characteristics of the liquid film seal are investigated. The results presented are expected to enrich the theoretical basis of optimizing the dynamic performance of liquid film seals with textures.

The purpose of this paper is to investigate the dynamic characteristics of spiral groove liquid film seal under the effect of thermal–fluid–solid coupling.

The dynamic analysis model of spiral groove liquid film seal under the effect of thermal–fluid–solid coupling was established by perturbation method. The steady-state and perturbation Reynolds equations were solved, and the steady-state sealing performance and dynamic characteristic coefficients of the liquid film were obtained.

Compared with the liquid film without coupling method, a divergent seal gap is formed between the seal rings under the effect of thermal–fluid–solid coupling, the minimum liquid film thickness decreases, the dynamic stiffness and damping coefficients of the liquid film are increased and the thermoelastic deformation of the end-face improves the dynamic performance of the liquid film seal.

The dynamic characteristics of the spiral groove liquid film seal under the effect of thermal–fluid–solid coupling are studied, which provides a theoretical reference for optimizing the dynamic performance of the non-contacting liquid film seal.

The purpose of this study is to investigate the sealing performance of S-CO₂ dry gas seals (DGSs) by considering the effects of pressure-induced deformation, thermal deformation and coupling deformation.

A hydrodynamic lubrication flow model of S-CO₂ DGS was established, and the model was solved using the finite difference and finite element methods. The pressure-induced deformation and thermal deformation of the sealing ring, as well as the sealing performance under the effects of pressure-induced deformation, thermal deformation and coupling deformation, were obtained.

The deformation of the sealing ring is mainly thermal deformation. The influence of pressure-induced deformation on leakage and gas film stiffness is greater than that of thermal deformation and coupling deformation. However, thermal deformation has a greater impact on friction torque and minimum film thickness than pressure-induced deformation and coupling deformation. The influence of deformations on sealing performance is important.

The sealing performance of S-CO₂ DGSs was analyzed considering the effect of pressure-induced deformation, thermal deformation and coupling deformation, which can provide a theoretical basis for S-CO₂ DGS optimization design.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-04-2023-0120/

The purpose of this paper is to investigate the monitoring of the friction condition of mechanical seals.

Acoustic emission signals from the friction of the seal end face were obtained, and their bispectral characteristics were extracted. The variation of non-Gaussian information with the degree of friction was investigated, and by combining bispectral characteristics with information entropy, a bispectral entropy index was established to represent the friction level of the seal end face.

In the start-up stage, the characteristic frequency amplitude of the micro-convex body contact is obvious, the friction of the end face is abnormal, the complexity of the system increases in a short time and the bispectral entropy rises continuously in a short time. In the stable operation stage, the characteristic frequency amplitude of the micro-convex body contact varies with the intensity of the seal face friction, the seal face friction is stable and the bispectral entropy fluctuates up and down for a period of time.

The bispectral analysis method is applied to the seal friction monitoring, the seal frequency domain characteristics are extracted, the micro-convex body contact characteristic frequency is defined and the bispectral entropy characteristic index is proposed, which provides a certain theoretical basis for the mechanical seal friction monitoring.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0242/

The purpose of this paper is to investigate the effects of surface topography, including surface roughness, waviness and taper, on the cavitation of liquid film lubricated mechanical seals (LFL-MS).

A universal governing equation considering cavitation is established, and an equivalent relative density is defined to characterize the cavitation degree. The equation is discretized by the finite volume method and solved by the Gauss–Seidel relaxation scheme.

Results indicate that both radial length and a circumferential width of the cavitation zone and cavitation degree are affected significantly by the waviness amplitude and taper, but the effect of surface roughness is limited.

Effect mechanism of surface topography on the cavitation of LFL-MS is investigated and cavitation degree is reflected by an equivalent relative density. The results further help to comprehensively explore the cavitation mechanism.

This paper aims to investigate the influence of sinusoidal texture (ST) with different morphology parameters on the corresponding tribological effects.

The STs with different amplitudes, ranging from 0.05 to 0.3 mm, and frequencies, ranging from 5 to 17.5, are fabricated using nanosecond pulsed laser equipment. The friction experiments and the finite element analysis method are combined to investigate the tribological properties, under dry friction conditions.

Test results show that when the amplitude is 0.15 mm and frequency is 10, ST surface has the lowest friction coefficient of 0.373, and exhibits great anti-friction effect. It also possesses a complete texture edge after friction. The friction reduction effect of ST with larger or smaller amplitude and frequency is worse.

The results of this study can provide a guidance for the design optimization of ST of reciprocating sliding contact surfaces, under dry friction conditions.